IPL Depilator's Principle
The principle of photonic hair removal is to use the selective photopyrolysis of the patented strong pulsed light source to irradiate the normal epidermis without damage, penetrate the skin directly to the root of the hair follicle, and the melanin in the hair dry and hair follicle is absorbed and converted into heat energy, thus increasing the temperature of the hair follicle. When the temperature rises high enough, the follicle structure is irreversibly damaged, and the damaged hair and follicles are removed through a natural physiological process without damage to the surrounding tissue, resulting in painless hair removal.
Hair Management Process
★ In test before use It is strongly advised to check for adverse reaction by conducting a skin test 2 hours in advance of any hair removal procedure. ● Text method: On a small area of skin on the inside of the upper arm(the medial). From a low energy to high energy apply 1-2 times at the same place. After 2 hours if you feel redness, burns, stabbing painor other symptoms consult a doctor before using again. On slight discomfort, use the product again on a lower intensity setting, owever if discomfort continues, consult a doctor before further use.
Operating Steps
★ Clean the flash window, then shave the hair on your body and clean the residual hair. ★ Start the device, choose the best suitable intensity level to hair removal. ★ After finish hair removal, you should cool the skin using Ice water or a cold damp towel. ★ You can use a toner to help your skin retain moisture after hair removal. ★ Suggestions about intensity level operations for all types of skin and different parts of the body, please refer to the below comparison table. ★ It is strongly suggested you do not sure multiple times on the same part of skin. You should flash less than two times in succession only at one location. The operation frequency times should be reduced when using high energy intensity level. Note: ● Using for 6-10 times as a hair removal cycle. ● Use one time every two weeks for up to six times ● Use one time every four weeks when using 6-10 times ● If you find new thin hair grow after use it, operate one time every 2-3 months at this place, and continue gaining satisfying results. ● To gain the best results it is suggested that on areas of thick hair you use many times over a period of time. ● Use will vary from person to person, use less frequently when hair area grows by a small amount, about 30%.
Intensity Level and Skin Color Contrast Table
★ Using for 6-10 times as a hair removal cycle. ★ Use one time every two weeks for up to six times ★ Use one time every four weeks when using 6-10 times ★ If you find new thin hair grow after use it, operate one time every 2-3 months at this place, and continue gaining satisfying results. ★ To gain the best results it is suggested that on areas of thick hair you use many times over a period of time. ★ Use will vary from person to person, use less frequently when hair area grows by a small amount, about 30%.
Device Operation Notes
● Do not flash near or directly at the eyes when in use. ● After operation, some skin redness is a normal you can cool the area with ice water or cold damp towel. ● Do not clean the flash window directly with spray alcohol. ● Do not use in conjunction with other cosmetics such as water gel products. ●Try not to eat light sensitive food during operation (such as spinach,cole mustard, etc.). ● For best results use the higher energy setting.(Warning - only after following the previous instructions). ● The darker your skin any skin reaction may not be so apparent and the reaction may be delayed, in this case ensure the 2 hour waiting period is followed before increasing the intensity setting. ● Continue to look after you skin moisturizing and using Sun block in a normal way after using this product. ● Avoid UV light during use and always protection your skins when out in sun. Also try to Avoid long exposure to computer radiation when working, protecting yourself with sun block or sunscreen. ● Do not block the Air inlet and the cooling outlet so as not to affect the cooling of the device. ● Hair stuck to the device may cause some blank spots but it does not affect the performance of the device and the normal use. ● In the late period of life, the inner wall of the Light bulb will appear different degrees of black phenomenon, this is a result of the normal aging process of the tubes. Don't worry to continue to use as normal within the specified parameters. ● This product is not waterproof, avoid contact with water. ● Any faults, immediately unplug the device, if you find the factory for maintenance. ● Do not store the device near Strong magnetic fields, moisture dustor at high temperatures. ● Avoid damage and keep out of the reach and sight of children. ● Prohibit using it with other application which is not allowed ● Prohibit other people opening this device except our authorized persons otherwise ie may be danger electric shock.
